Electrical Engineering, Compliance, Standards and System Fundamentals

التذاكر

Electrical Engineering, Compliance, Standards and System Fundamentals

Electrical Engineering, Compliance, Standards and System Fundamentals
29 - 02 ديسمبر 2024
Kuala Lumpur, ماليزيا
ماليزيا

What are the Goals?

By the end of this Electrical Engineering, Compliance, Standards and System Fundamentals training course, participants will be able to:

  • Discuss the basic principles of ohm’s law and a variety of electrical calculations
  • Elaborate on the dangers of Electricity
  • Demonstrate methods of basic and fault protection methods
  • Identify permit systems, integrated safe systems of work and safe isolation procedures
  • Identify a variety of power supplies
  • Use a variety of electrical test equipment
  • Identify Electrical Earthing systems
  • Select and apply a variety of circuit protection systems and devices
  • Elaborate on electrical connections and switching devices
  • Discuss applications of several different types of Electrical Motors
  • Develop skills to enable the use of Electrical drawings and diagrams

Who is this Training Course for?

This Electrical Engineering, Compliance, Standards and System Fundamentals training course is suitable to a wide range of professionals but will greatly benefit:

  • Electrical and Instrument Technicians.
  • Electrical and Instrument Engineers.
  • Personnel whose work involves construction of equipment and systems
  • Supervisors
  • Design Engineers (for understanding of Installation and Maintenance techniques)
  • Mechanical Maintenance Technicians
  • Mechanical Maintenance Engineers
  • Staff who work in a limited capacity with Electrical systems
  • Non electrical personnel

Daily Agenda

Day One: Introduction, Health and Safety and Electronics

  • Pre-course Assessment
  • Introduction
  • Principles of Health and Safety
  • Electricity at work regulations
  • Personal protective equipment
  • Basic principles of Ohms law
  • Series and parallel circuits
  • Hazards of electricity
  • Electric shock

Day Two: Circuit Protection, Power Transmission, Power Supplies, Power Distribution and Test Equipment

  • Recap on day 1
  • Safe isolation
  • IP ratings
  • Circuit protection concepts
  • Circuit protection devices
  • Measurement devices
  • Multi-meters
  • Voltage indicators
  • Oscilloscopes
  • Current measurement
  • Power distribution and transmission

Day Three: Earthing Systems, Circuit Protection, Electrical Connections, Inspection and Testing

  • Recap on day 2
  • Standards (IEC 60364)
  • Earthing applications
  • TNCS Earthing systems
  • TNS Earthing systems
  • TT Earthing systems
  • IT Earthing systems
  • Fuses, circuit breakers and additional circuit protection
  • Electrical connections
  • Electrical Inspection techniques
  • Testing – Continuity of CPC’s
  • Testing – Ring-final continuity
  • Testing – Insulation Resistance

Day Four: Inspection & Testing and Motor Applications

  • Recap on day 3
  • Testing – Polarity
  • Testing – Earth Electrode Testing
  • Testing – Earth-loop impedance
  • Testing – RCD Testing
  • 6 steps to fault finding
  • Preventative maintenance
  • Reactive Maintenance
  • Introduction to Motors
  • Types of Motor (A.C. 3-Phase)
  • Types of Motor (A.C. Single-Phase)
  • Types of Motor (D.C.)
  • Methods of starting Motors
  • Schematic diagram development and interpretation

Day Five: Motors, Starting Techniques and Advanced Motor Logic

  • Recap on day 4
  • Types of Motor (D.C.)
  • Methods of starting Motors
  • Schematic diagram development and interpretation
  • PLC’s and Ladder logic
  • End of course Assessment

التذاكر

الوقت والتاريخ
الأحد، 29 ديسمبر 2024
البداية - 11:00 ص (Asia/Kuwait)
الخميس، 2 يناير 2025
النهاية - 11:00 ص (Asia/Kuwait)

إضافة إلى التقويم

الموقع

Kuala Lumpur

Kuala Lumpur
ماليزيا
--Kuala Lumpur--

احصل على الاتجاه

منظِّم

Seattle International For Training

info@seattle-int.com
مشاركة

تعرف على آراء الجمهور عن هذه الفعالية، ثم انضم إلى المحادثة.