Electrical Engineering, Compliance, Standards and System Fundamentals
التذاكر
تم إغلاق التسجيلات
Electrical Engineering, Compliance, Standards and System Fundamentals
Electrical Engineering, Compliance, Standards and System Fundamentals
23 -
27
يونيو
2024
London,
المملكة المتحدة
What are the Goals?
By the end of this Electrical Engineering, Compliance, Standards and System Fundamentals training course, participants will be able to:
- Discuss the basic principles of ohm’s law and a variety of electrical calculations
- Elaborate on the dangers of Electricity
- Demonstrate methods of basic and fault protection methods
- Identify permit systems, integrated safe systems of work and safe isolation procedures
- Identify a variety of power supplies
- Use a variety of electrical test equipment
- Identify Electrical Earthing systems
- Select and apply a variety of circuit protection systems and devices
- Elaborate on electrical connections and switching devices
- Discuss applications of several different types of Electrical Motors
- Develop skills to enable the use of Electrical drawings and diagrams
Who is this Training Course for?
This Electrical Engineering, Compliance, Standards and System Fundamentals training course is suitable to a wide range of professionals but will greatly benefit:
- Electrical and Instrument Technicians.
- Electrical and Instrument Engineers.
- Personnel whose work involves construction of equipment and systems
- Supervisors
- Design Engineers (for understanding of Installation and Maintenance techniques)
- Mechanical Maintenance Technicians
- Mechanical Maintenance Engineers
- Staff who work in a limited capacity with Electrical systems
- Non electrical personnel
Daily Agenda
Day One: Introduction, Health and Safety and Electronics
- Pre-course Assessment
- Introduction
- Principles of Health and Safety
- Electricity at work regulations
- Personal protective equipment
- Basic principles of Ohms law
- Series and parallel circuits
- Hazards of electricity
- Electric shock
Day Two: Circuit Protection, Power Transmission, Power Supplies, Power Distribution and Test Equipment
- Recap on day 1
- Safe isolation
- IP ratings
- Circuit protection concepts
- Circuit protection devices
- Measurement devices
- Multi-meters
- Voltage indicators
- Oscilloscopes
- Current measurement
- Power distribution and transmission
Day Three: Earthing Systems, Circuit Protection, Electrical Connections, Inspection and Testing
- Recap on day 2
- Standards (IEC 60364)
- Earthing applications
- TNCS Earthing systems
- TNS Earthing systems
- TT Earthing systems
- IT Earthing systems
- Fuses, circuit breakers and additional circuit protection
- Electrical connections
- Electrical Inspection techniques
- Testing – Continuity of CPC’s
- Testing – Ring-final continuity
- Testing – Insulation Resistance
Day Four: Inspection & Testing and Motor Applications
- Recap on day 3
- Testing – Polarity
- Testing – Earth Electrode Testing
- Testing – Earth-loop impedance
- Testing – RCD Testing
- 6 steps to fault finding
- Preventative maintenance
- Reactive Maintenance
- Introduction to Motors
- Types of Motor (A.C. 3-Phase)
- Types of Motor (A.C. Single-Phase)
- Types of Motor (D.C.)
- Methods of starting Motors
- Schematic diagram development and interpretation
Day Five: Motors, Starting Techniques and Advanced Motor Logic
- Recap on day 4
- Types of Motor (D.C.)
- Methods of starting Motors
- Schematic diagram development and interpretation
- PLC’s and Ladder logic
- End of course Assessment
التذاكر
تم إغلاق التسجيلات
دورات ذات صلة
Business Improvement & Quality Techniques
01 -
05
ديسمبر
2024
Kuala Lumpur,
ماليزيا
Compliance Regulatory Professionals
01 -
05
ديسمبر
2024
Dubai,
الإمارات العربية المتحدة
API 2201: Procedures for Welding of Hot Tapping Equipment
01 -
05
ديسمبر
2024
Cairo,
مصر
API 510: Pressure Vessel Inspection Code (API Exam Preparation Training)
01 -
05
ديسمبر
2024
Barcelona,
إسبانيا
API 521 : Pressure Relieving and De-Pressuring Systems
01 -
05
ديسمبر
2024
London,
المملكة المتحدة
API 570 : Piping Inspection Code (API Exam Preparation Training)
01 -
05
ديسمبر
2024
Kuala Lumpur,
ماليزيا
API 580/581/ASME PCC-3: Risk-based Inspection Program, Technology and Planning Methods
01 -
05
ديسمبر
2024
Dubai,
الإمارات العربية المتحدة
API 598: Valve Inspection & Testing
01 -
05
ديسمبر
2024
Istanbul,
تركيا
API 620/650/651: Design, Fabrication, Erection, and Inspection of Welded and Large Low-Pressure Welded Storage Tanks and Their Cathodic Protection
01 -
05
ديسمبر
2024
Cairo,
مصر
Pre-Contract Risk Assessment in the Oil & Gas Industry
01 -
05
ديسمبر
2024
Istanbul,
تركيا