ASME B31.3 Process Piping Design Code

التذاكر

ASME B31.3 Process Piping Design Code

ASME B31.3 Process Piping Design Code
15 - 19 ديسمبر 2024
Madrid, إسبانيا
إسبانيا

What are the Goals?

  • The aim of this comprehensive training course is to provide the delegates with enough knowledge and skills about process piping related ASME B31.3
  • Identify the design of piping flanges and blanket
  • Welding and Brazing Qualification, procedures Specifications
  • Explain the Fabrication, Assembly, and Erection and identify the required inspection and testing Define hydrostatic pressure and hydrostatic-pneumatic tests
  • Receive the enough information about the Fluid Service Requirements for Materials
  • Explain of nonmetallic piping design, Fluid Service Requirements, inspection and testing
  • Employ pre and post weld heat treatment and identify the Charpy impact testing

Who is this Training Course for?

This training course is suitable to a wide range of professionals but will greatly benefit:

  • QA/QC inspectors
  • Maintenance Engineers
  • Inspection & testing professionals
  • Fabrication Engineers
  • QA/QC reliability professionals for oil and gas (Petrochemical and Refining) operations
  • Fresh graduates, piping engineers and designers

Daily Agenda

Day One

  • Introduction and history of ASME codes
  • Scope and Definitions
  • Content, Coverage and Exclusions
  • Design include Design Pressure, Design Temperature
  • Listed Components Unlisted Components
  • Allowances for Pressure and Temperature Variations
  • Allowable Stresses and Other Stress Limits
  • Bases for Design Stresses
  • Casting Quality Factor, Ec and Weld Joint Quality Factor, Ej
  • Pressure design of components
  • Branch Connections
  • Pressure Design of Flanges and Blanks
  • Fluid service requirements for piping components and piping joints

 Day Two 

  • Flexibility and support
  • Chapter iii materials
  • Listed Materials, Unlisted Materials. Unknown Materials. Reclaimed Materials.
  • Lower Temperature Limits
  • Impact Testing Methods and Acceptance Criteria
  • Fluid Service Requirements for Materials
  • Chapter IV Standards for Piping Components
  • Chapter V Fabrication, Assembly, and Erection
  • Welding and Brazing Qualification, procedures Specifications.
  • Preheating
  • Heat treatment requirements
  • Bending and forming
  • Assembly and erection

Day Three

  • Chapter VI Inspection, Examination, and Testing
  • Responsibility and qualifications for Inspection and examination
  • Extent of Required Examination
  • Radiographic and Ultrasonic Examination
  • Testing Required Leak Test
  • Hydrostatic Leak Test
  • Pneumatic Leak Test
  • Hydrostatic-Pneumatic Leak Test

Day Four

  • Chapter VII Nonmetallic Piping and Piping Lined with Nonmetals
  • Pressure design of piping components
  • Fluid service requirements for nonmetallic materials
  • Materials general requirements
  • Fabrication, assembly, and erection
  • Inspection, examination, and testing
  • Chapter viii piping for category M Fluid Service

 Day Five

  • Chapter IX High Pressure Piping
  • Chapter X High Purity Piping
  • Review codes appendix
  • Review of codes tables

التذاكر

الوقت والتاريخ
الأحد، 15 ديسمبر 2024
البداية - 11:00 ص (Asia/Kuwait)
الخميس، 19 ديسمبر 2024
النهاية - 11:00 ص (Asia/Kuwait)

إضافة إلى التقويم

الموقع

Madrid

Madrid
إسبانيا
--Madrid--

احصل على الاتجاه

منظِّم

Seattle International For Training

info@seattle-int.com
مشاركة

تعرف على آراء الجمهور عن هذه الفعالية، ثم انضم إلى المحادثة.